Archive:2009 Brian Waddington hut renovations

Projects

Add screens

Christian has screens in apartment.

Costs

• $100 screens
• something to attach

Stuff to buy

Something to attach them

Tools

Adult size metal hacksaw up there already. Screwdriver?

Add curtains

Line will pre-make curtains...

The 7 windows are:

• (4) 29 1/2 x 41 1/2
• (2) 29 1/2 x 31 1/2 (by stove area)
• (1) 25 1/2 x 25 1/2 (diamond)

Stuff to buy

Curtains? Tea hooks 4x7 = 28

Double pane the windows

Mostly done. Possibly move some outside?

Need a few more clips. Clips and screws are up there. Needs caulking.

Costs

$410 more or less

Stuff to buy

• caulking

Tools

• caulking gun
• screwdriver

Fix the roof

Stuff to buy

• Al sheeting
• expanding foam
• roofing screws
• asphalt caulking

Tools

• caulking gun
• brace n bit
• tin snips

Roof gear

• harness
• rope(s)
• aider
• knee pads
• foamy
• biners
• prussiks

Costs

$250

Paint the inside walls

According to my measurements the circumference of the hut is ~26m, the first floor is 3m tall with 1.8m of that non-wainscoting, and the "roof/wall" upstairs is 3.6m. This makes the following paintable areas:

Ground floor: 26x1.8=46.8 m^2 (wall above wainscoting, includes some windows and cupboards) 26x1.2= 31.2 m^2 (wainscoting surface area, if we decide to paint it, includes some cupboards)

Upstairs: 26x3.6=93.6 m^2 (it's probably a fair amount less, since this gives the end walls more area than they deserve - but we're approximating)

Trim/cupboards(?): ~5 m^2

Notes

Probably need:

• paint or stain
• rollers etc.

Stuff to buy

Exterior stain.

Tools

• Rollers
• Brushes
• Roller trays
• metal edge protector
• scraper

Paint the unpainted bench/table

Done. Can use another coat, to use up paint up there.

Tools

• Brushes

Move the outhouse

Notes

The outhouse is getting full. Renovation includes (1) deciding if it is full yet, and if so, (2) looking for a new site that will not drain into the lake but is still close enough to be used, (3) digging a really big hole that will last for years but hopefully not hit water. (4) Carefully taking apart the outhouse and carrying the pieces to the new site (5) Assembling the outhouse (6) We are done, but we should carry out any debris from previous failed outhouse attempts. None of this should be costly. Re-painting is probably not a priority.

Costs

None of the above will require spending money, but we need about 4 people x 1 day.

Required Tools

Screwdriver, hammer, dirt digging shovels.

Refinish the floor

More tong oil?

Maybe leave it for next time.

Notes

Refinishing the floor is a major task. Normally you would use a huge power sander to remove the old finish and flatten the floor. This will be extremely difficult and labour intensive using only hand tools.

At least two coats of finish will be needed, with 12 hours or so to dry between coats (for floors, the finish has to dry enough that you can walk on it lightly while applying the next coat). After completion, there should probably be no heavy use for a week. No one can be in the hut doing any other work while the floor is drying. Probably no one will want to sleep inside either.

Equipment / supplies needed:

• sanding implements - normally power sanders are used for refinishing floors. For a manual approach, several half sheet (or larger) sanding blocks will be needed so multiple people can work at the same time.
• Dust removal - a vaccum cleaner would be ideal, but it we are less picky we can sweep up the dust.
• Finish

Costs

$150 for finish - urethane or similar. Sand paper - $100 (in the case of manual sanding, expensive fancy sandpaper will cut the manual effort by about half).

Add extra rails to honeymoon suite

Notes

Ideally these would be done well if we do them at all, ie. vaguely matching wood, non-flimsy attachment/construction (otherwise they're probably worse than nothing)

Costs

$100

Increase ventilation

Maybe remove loovers? Some pliers and some thought for next time. Maybe plug old hole...

Tools

pliers

Bridge/Trail around lake

Notes

Probably need:

• gabian cages
• expanded metal for bridge deck
• miscellaneous hardware, bolts etc.
• signage to tell people to stay on the trail

Costs

$200

Haul out accumulated Junk

Notes

We may make several trips from the cars to the Hut bringing in tools, materials, food, beer, etc, so on the way out we might haul some of the accumulated junk. Some of the things we might consider hauling out if we have enough personnel, include

• empty propane tank
• several empty kerosene cans
• several empty garbage cans modified for composting poop
• the two lead-acid batteries if they are indeed beyond help.
• abandoned spondonicles, dishes, etc
• construction debris if it is known to be useless.
• empty paint tins
• two kerosene heaters
• broken Coleman stoves

Costs

If we haul in a couple cans of white gas, this will help with drying out the hut before painting it. $25

• beer
• food

Notes

The vent holes are 5" in diameter.

Other measurements, while I'm looking at this ready-to-be-lost piece of paper:

Windows could be plexiglassed on the inside fairly easily. Requires: 4x 29.5" x 41.5" 2x 29.5" x 31.5" 1x 25.5" x 25.5" And some clips around the outside (bathroom mirror style). Note that the glass can't much bigger, otherwise it will interfere with the latches. Can't be much smaller either. The plexiglass will be right on frame/retainer interface (ie - the same size as the glass), so clips with some length would be good so they are further from the edge (reduce chance of splitting). Pre-drill the holes.

Measured from the inside, accurate enough to figure out how much paint we need:

• Main Floor:

Length of hut - 7.3m Width of hut - 3.9m Length of vestibule - 1.8m Height above wainscoting - 1.8m Ceiling height - 3m

Beams are 24" around (8" against wall or 6" free standing): 10x 3m 20x 1.2m 20x 3.9m

Unpainted table - 3'x6' 2x Unpainted benches - 1'x5'

• Loft:

Length of hut - 7.3m Width of hut - 3.9m Length of 'roof/wall' - 3.6m Length of vestibule - 2.2m (yes longer than downstairs - it's not as high and the roof slopes) Length of 'roof/wall' in vestibule - 2.3m

Beams are 24" around 8x 3.6m 20x 1.5m

Other thoughts: More mallion and chain for lanterns trim for messy paint jobs? paint the ladders? floor appears to be sealed already - should we do it again? outside paint seems to be alright - should we do it again? railing for upstairs traverse to honeymoon suite? (2x1.6m posts, 2x1.6m rails) plexiglass on inside better - glass absorbs UV without turning opaque. The "Brian Waddington Hut" wood sign is still only half complete. A chisel could fix this quickly. Vents suck, and only sort-of open. Maybe a simple tube, pointing down, that cannot be closed, would be good. Or supply a cap which can be taken on/off - this would be less confusing than the 'rotate 180 degrees and wonder whether it was open or closed to start with' vents we have now. Plastic probably gathers less condensation than metal. Roof doesn't appear to be leaking enough to see it inside anymore, probably could still use some repair.

When deciding how much to do, we need to keep in mind whether is it a helicopter job or a carry in job. In my mind (and probably the club's budget this summer) it is a carry-in job. We can still make the required big improvements carry-in style, but maybe won't have enough man-power to carry enough paint for both inside and outside. I guess we'll see. Probably a good way to do it would be to conscript some porters for a work weekend and a small number of people to stick around for a few extra days.

Also, the hut seemed plenty warm with just the two catalytic heaters and 11 people (there were some french people up there too. The big catalytic is harder to light (you're supposed to use some alcohol-based priming fluid, which we did not have). Not Brew Hut warm, but I had to unzip my sleeping bag.

Progresss Report and What Remains to be Done --after Reno(1)

Objectives: To control the excessive dampness and moldiness. To make it warmer. To make it nice. To make it easier to keep clean. To reduce deterioration.

Work is easier and less overwhelming if people coming up to the Hut to work, have an idea what they want to do when up there, and this also makes it easier to ensure that the proper tools and materials are available. If you see something that you would like to do/finish, please adopt it as yours.

Most of the incomplete projects listed below, are not lacking in materials or in planning; all we need is personnel with time to do the work.

Solar Air Heater

It's installed and working as expected. We need to plug the old five-inch hole above the upstairs south window so it doesn't leak air. Probably a piece of plywood nailed over the hole, maybe with some insulation stuffed inside, would do the job. Need to use the ladder for this. We should modify the vent at the north end of the hut, so that it cannot be shut off.

The lead-acid batteries left over from the composting toilet and weighing 63 lbs each, are probably toast as they have been discharged until they read 1.5 volts, whereas they should not normally be discharged below about 11 volts. They are being trickle-charged with spare current from the photovoltaic panel, and on a sunny day probably receive 0.2 ampere hours of charge current. Whether the charge is retained, is not known.

We should decide if there is any real intended use for these batteries and whether they have sufficient capacity that they can be used for this intended use. If either of these answers is "NO", then they should be carried out. Little led lights are cute, but random wiring is dangerous, and most everybody up there has a headlamp and doesn't need little led lights. We would prefer that users of the Hut not be encouraged to modify the wiring.

There's a few other items left over from the days of the composting toilet, which could be carried out, but they aren't nearly as challenging as the batteries.

White Paint

We bought a 18.5 liter pail of "mistint paint", which usually means it is a color nobody wanted, but in this case it meant the pail had leaked air and formed a skin on the paint. We poured the paint through a screen to take out the skin and filled five, one gallon cans with the lump-free paint so it could be carried. We worried that it might be difficult to find people to carry the paint to the Hut, but Simen said "how many cans do you want me to carry?" In the end he carried four of the cans. Thanks, Simen.

We have applied a thin coat of Premium Alkyd Eggshell white (diluted 10% with thinner) to all interior plywood surfaces. Because the wood is weathered from being ignored for ten years, this has not covered the thin cracks in the wood. But it looks good, and it should stop a lot of moisture from soaking into the walls to feed mold. A second coat would be good, but would require buying another 4 gallons of paint, hauling it up there and getting a crew to apply it. We might need a different crew, because the original paint crew might be all used up. There's three roller cages, two new rollers, two trays, and half a gallon of paint up there that can be used for touching up anything that looks too thirsty.

The smell of paint will become less in a couple of weeks. We slept in the paint fumes the night after we painted it, and it was tolerable. It will get better.

Tung Oil

All beams, even the difficult ones, have received one coat of oil, and they look really good. There's a liter of oil and a liter of oil mixed with something (kerosene?) up there. The mixed oil is good for re-coating any beams that look thirsty but already have some oil on them. To re-coat beams we need cheap paint brushes, and rags. These are up there, ready to be used. Somebody working for about four hours could use up the rest of the oil.

Kitchen Cupboards etc

The upper kitchen cupboards were beautifully stained "red oak on maple". These need a second coat of urethane in a few weeks. The lower cupboards need to be similarly treated. The kitchen counters were covered with sheet aluminium. We may want to caulk under the edges because when spilled soup gets between the aluminium and the maple counter top, it will stay there and further damage the counter top. We have the stain, the urethane up there; need small paint brush, rags, caulking, and some time.

Exterior Trim

There's a can of oil-based trim stain up there and the trim sure would look better if it was re-stained. Need a wire brush to remove the old peeling stain, and some way to reach the high trim boards (ladder).

S Window

Really big windows are nice; they let in lots of light. But really big windows put a lot of strain on the frame and hinges. The downstairs south window frame is in bad shape. The window can only be closed using a hammer. Options include nailing it shut, taking the frame apart and epoxying the cracks and planing it smaller, or changing the whole style so it still opens inwards but swinging "hinged" at the bottom rather than at the side. They don't even need hinges or hardware; they are held closed with wooden wedges, and they do not get snow buildup. Both Scott Nelson and Steve Mullen know about windows that open this way.

Double Glaze Windows

Some windows need more little plastic clips installed. They and the screws, are up there. We could caulk the windows with special caulking, which is up there.

Mosquito Screens

They are partially installed, but unfortunately an essential part was lost preventing the assembling of the final screen. And a ladder is needed for installing the upper screens. The ladder is up there but it was being used for roofing.

Curtains

The Curtain Committee has provided curtains to keep in heat at night. These need to be installed. The entranceway curtains maybe should be re-installed, (they were taken down for painting) though they make the entranceway cold and a place for condensing of moisture, attracting mold.

Interior Decoration, Signeage, etc

This was all taken down for painting and needs to be put up. The sign about paying, etc needs to be much better; currently it's written in pencil and partially scratched out. See the signage at Brew for details. In general we need fewer and more comprehensive signs. A paragraph describing what to do when leaving, might avoid the unfortunate happening a couple years ago where somebody left the upstairs window open and the upstairs filled with blowing snow.

Porcupine Deterrent

Nasty scratchy stucco mesh was installed and now no creatures larger than a mouse can get under the Hut. Some of the plywood skirting has been eaten by porcupines. To stop this, a huge amount of wire mesh, or stucco mesh, or something, would have to be applied to the skirt going around the Hut.

Drainage around the Hut

Some ditching was done to divert the water from the large melting pile of snow behind the Hut. There are proper drain pipes installed below surface, and they seem to be doing their job of keeping the ground from being soaked, deeper down. In a couple of weeks the large pile of snow should be gone.

Garbage Hauling

A lot of accumulated junk was hauled out, including the two old kerosene heaters and a propane heater and tank, some things left over from the composting privy, etc. There's some steel cable still up there; might be good for building a bridge at the lake outlet. There's some Dexion handy angle that might not be good for anything.

Roof

For most of the roof, foam has been installed under the ridge cap. When the foam ran out, the job was finished with a couple of tubes of caulking. Maybe the Roof Committee can comment, but the roofing job is probably finished.

The main objective of the roof maintenance was to seal the gaps beneath the main ridge cap. This is done (with foam and tar caulk). This should drastically improve the mildew situation near the roof beams. However the large gap under the ridge cap above the Honeymoon Suite still needs to be covered with sheet metal (already up there). This job will need 2 people on the roof at once and requires the corrugated sheet metal panels be unscrewed and lifted. Probably about a 1/2 days job. It has been suggested to me that this part of the roof doesn't see as much wind, so it's likely that less snow gets under the cap and melts, plus I sealed some of the area under the cap with tar. This job probably isn't high priority, but the sheet metal to do it is up there.

Outhouse, or Privy

We think it's getting full, but we don't want to look too close. If we can find a new spot for a hole, not too far away from the present hole, we may be able to brute-force it over to the new location. Otherwise it must be taken apart and re-assembled over the new hole.

Trail around north side of Lake

We noticed the north side is clear of snow, and there aren't many boulders to get around. And both Scott Nelson and Veenstra like building bridges, so a bridge across the creek at the lake outlet, and a trail around the north side will probably get built, next reno trip.